Professional Car Diagnostic Tools, Complete System, 28 Resets Car OBD2 Scanner

Description: 2024 Version MUCAR VO6: No IP Limit, For More Features, Newer Vehicles, Better Performance, First Choice of Millions of Car Repair Shops, Workshops and Mechanics!!! ️BIGGER, ️FASTER, ️MORE FUNCTIONS, ️MORE NEWER VEHICLE COVERAGE, ️MORE POPULAR than other similar diagnostic scan tool. MUCAR VO6 Make Automotive Repairs Easy, Efficient, Accurate, and Affordable OE-Level Full Systems & Subsystems Diagnosis Lifetime Free :Engines, Transmission, Airbags/Immobilizer, IMMO Key Coding, ABS, Cruise Control, Instruments, Self Leveling Suspension systems, Seats, Doors, Gateway, Steering Angle, Air Suspension, Body Systems, Electronic Power Steering & Motor Assisted, Power Steering, Tyre Pressure, Rain Sensors, 4WD System, etc. 28 Reset Functions Lifetime Free:OIL(Oil Light Reset), SAS(Steering Angle Calibration), Injector Coding, IMMO Key Programming, ABS Bleeding, AdBlue, ETS(Throttle Matching), TPMS Reset, EPB Reset, Tire Reset, AFS Headlamp Reset, Sunroof Initialization, BMS(Battery Reset), Seat Calibration, SRS(Airbag Reset), A/F Reset, Gearbox Reset, Transport Mode, Windows Calibration, Language Change, Suspension Reset, ODO Mileage Reset, etc. Support ODO Reset a)ODO reset is to copy,write,or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable,so that the odometer shows the actual mileage. b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure,it is necessary to do ODO reset after maintenance. This feature is available for limited cars, including Chrysler 200 after 2010, Chrylser 300C before 2010, Chrylser Aspen after 2006, Chrysler Avenger after 2007, Chrysler Caliber after 2006, Chrysler Caravan after 2012, Chrysler Charger after 2004, Chrysler Durango after 2007, Chrysler Journey after 2008, Chrysler Liberty after 2008, Chrysler Magnum after 2004, Chrysler New Sebring after 2007, Chrysler Ram after 2006, Chrysler Voyager after 2015, Buick Enclave 2007-2013, Chevrolet Equinox 2008-2009, Pontiac Torrent 2007-2013, Saturn Outlook 2007, Nissan Datsun 2016-2018, VW Golf 2009-2014, VW Passat 2011-2018, VW Polo GTI 2012-2015, VW Tiguan 2009-2015. Full OBDII Special Functions (10 Modes): Read Codes, Clear Codes, Freeze Frame Datas, Live Datas, O2 Sensor Test, EVAP Systems, I/M Readiness, On-board Monitor, Vehicle Information, DTC Lookup. Bidirectional Control & ECU Coding:Paid upgrades functions, $49.95/year/1 Car brand,designed for advanced mechanics, automotive technicians, auto repair shops. If you need it, you can make an in-app purchase to get this functions in the MUCAR Store. Lifetime Free Update:One-click updates via Wi-Fi to the newest version. Load the latest version, bug fixes, new vehicle models coverage, newly added parameters, and functionality on your scanner. Auto VIN Scan + 106+ Brands and 20000+ Cars supported.:Supports 12V cars and light trucks (non-electric) manufactured in 1996 or later that are OBD II-compliant with 16-Pin OBD II protocols (KWP2000, CAN, ISO9141, ISO14229, J1850 PWM, and J1850 VPW). Powerful Datas Collection & Processing for Vehicles:Whole car auto scanning, automatically match proper software. 4 in 1 live data stream, data record, data playback, screen recording, screenshot save, google search online, diagnostic health reports, and diagnostic feedback. Diagnostic Data Manager: You can well manage the workshop information with all available functions within this application: Vehicle History, Workshop Information, Diagnostic Log, and Customer Manager. Intuitively look up the summarized details. 20 Languages Support:English, French, German, Italian, Spanish Portuguese, Japanese, Russian, Polish, Dutch, Hungarian, Slovak, Greek, Slovenian, Korean, Chinese Traditional, Swedish, Turkish, Czech, Indonesian language. Online Maintenance Resources:Operating skills, DTC help, automotive technical manuals, service cases, online support, remote techsupport and operating videos. Incoming tutorial videos of different functions will be gradually updated on the scanner. No matter for those who know how to do repair or not, it allows you to grasp and understand car breakdown problems more quickly. A Carry Bag Included:A protective carry bag is attached to the package. It is not only convenient to carry, but also provides excellent protection for the product. Mucar VO6 Provides OE-LEVEL FULL Systems Diagnoses + Full OBDII Special Functions+ Auto VIN + Lifetime Free Online Update Mucar VO6 diagnostic scan tool can accessALL available vehicle ECU systems and read ECU information to facilitate the vehicle diagnoses such as ECM(Engine System), ABS(Anti-Lock Brake System), SRS(Airbag System), TCM(Transmission System), TPMS(Tire Pressure Monitor System), SAS(Steering Angle System), BCM(Body Control System), EPB(Electric Park Brake System), EPS(Electric Power Steering System), AC(Air Conditioning System), IC(Instrument System) and Security System. Fast Scan and Read/Clear fault codes in seconds, effectively turn off the warning light. MUCAR VO6 Diagnostic Tool Provides Comprehensive 28 Maintenance Reset Services for LIFETIME FREE USE. Help You Target New Business. 1. Oil Reset The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle. 2. Elec.Throttle Adaption Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state. 3.Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering. 4. Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. 5. ABS Bleeding When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity 6.Break-pad Reset lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms. 7.DPF Regeneration DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. 8.Gear Learning After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed. 9. IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. 10. Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. 11.TPMS Reset Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions 12. Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration. 13. AFS Reset This feature is used to initialize the adaptive headlamp system. 14.A/T Learning This function can complete the gearbox self-learning to improve gear shifting quality. 15.Sunroof Initialization This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc. 16. EGR Adaption This function is used to learn the EGR valve after it is cleaned or replaced. 17.ODO Reset a)ODO reset is to copy,write,or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable,so that the odometer shows the actual mileage. b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure,it is necessary to do ODO reset after maintenance. 18. Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. 19. Transport Mode ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 20. A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 21. Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware). 22. NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu. 23. AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. 24.Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired. 25.Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. 26.Tyre Reset This function is used to set the size parameters of the modified or replaced tire. 27.Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. 28. Language Change This function is used to change the systems language of the vehicle central control panel. NOTE: List varies by vehicle's make, model, and year. NOT All Services work for All Cars. Please remember to contact sellers before buying to make sure the desired functions are compatible with your cars, which won't waste your time. :) You can also check the compatibility by yourself at MUCAR Official Site. Subscribe to Special Functions(49.95USD/YEAR/CAR BRAND) Makes VO6 Be A Professional Scan Tool - Suitable for Advanced DIYer and Professional Mechanics Active Tests/Bidirectional Control (Special Functions): Also called “actuation testing”, bidirectional control allows the mechanic to activate or test mechanical components on demand. This process tells you if individual actuators, valves, and pumps function the way they should, allowing for more efficient and effective repairs. ECU Coding (Special Functions): Helps Re-flash the hidden functions of vehicle control modules to achieve personalization, and helps initialize, match and reprogram adaptive data for certain components (ECU/modules) after making repairs or replacements. Compatible with vehicles worldwide -- Wide Range Of Suitable Models Support 106+ Car Brands, 20 languages and Continuous updates

Price: 482.4 USD

Location: China

End Time: 2024-10-25T07:34:56.000Z

Shipping Cost: 0 USD