Nautilis iRelay+ & iSpindel Pill-For better iSpindel signal,faster calibration!

Description: I have been a homebrewer for 10 years and have won 14 medals at home brewing competitions. Due to the fermentation in the stainless steel fermenter and the use of the iSpindel hydrometer, I was forced to invent a device that will amplify the signal and forward the data to the screen and further to the applications. I note that I invest all the profit from the devices in new beer devices and firmware upgrades so that everyone can enjoy this hobby even better. I would like to mention that you can find the instructions for connecting iRelay on my website nautilis.eu - By purchasing, you get the option to register on the Nautilis website and download all new upgrades for your device. I am at disposal for all your questions via email or social networks & for larger customers via mobile applications. iSpindel WiFi relay+ (iRelay Plus – USB-C) Additional thermometer & pressure sensoriSpindel WiFi relay is a device used for signal amplification and connection of a digital hydrometer – iSpindel, processing of received data and further distribution according to fermentation monitoring applications. The data measured by the hydrometer is displayed on a large TFT display, can be viewed via the local relay website or sent to the other suported applications where graphs, analytics, remote insight into the state of the fermenter and more are available. Now is possible to send hydrometer data to the following services: UbiDots, BrewSpy, Brewfather, Monitor.Beer, Grainfather, Little Bock, Brewers Friend, BrewBench, Blynk IOT, MQTT. The last time the hydrometer data was read, as well as the density, temperature, battery voltage, signal strength, name of the hydrometer, are shown on the device screen and website. The signal strength of the iSpindel WiFi relay was tested by placing the hydrometer in a 2 mm thick steel barrel and a 6 mm lid without a rubber seal with a stainless steel clamp system, and placed the barrel in a closed freezer. And in such conditions, the signal easily broke through to the hydrometer. Due to its extremely reliable connectivity, iSpindel consumes noticeably less power and thus lasts longer. iSpindel WiFi relay plus is powered by a 5V USB-C cell phone charger that can also be used to charge your hydrometer battery, and your power consumption is negligible. The iSpindel hydrometer no longer needs the Internet, and WiFi relay it doesn’t need either. Now the internet connection is only needed when you need a remote insight into the fermentation state via the previously mentioned applications. The gadget can greatly facilitate and speed up the calibration of the iSpindel hydrometer, as it displays an angle. The relay firmware is constantly being upgraded and improved. Firmware upgrades, if necessary, they upgrade wirelessly via OTA (Over the Air) and the device’s web interface. Currently 2 iSpindel hydrometers can be connected to the iSpindel WiFi relay. Any irregularities or warnings on the display are shown in red colour. A confirmation tone sounds when saving the settings and a continuous alarm occurs at too low or too high hydrometer temperature and when the specific gravity falls below the value you specify. iSpindel relay+ has posibility of entering OG for 2 hydrometers from which % ABV and attenuation are then automatically recalculated. The latest firmware has SG and temperature correction for both iSpindels applied to the Display and Blynk Application. The battery status of the iSpindel is displayed as a graphic icon showing the battery voltage and as a percentage of the remaining voltage. Next to the battery status icon is a graphic display of the signal strength according to the hydrometer, and next to it is a graphic display of the signal strength according to the home WiFi network. If the Relay is not connected to home WiFi then the “D” (Disconnected) mark is visible instead of the signal strength display. If you use Plato degrees instead of SG, then you can change the density unit for each iSpindel in the settings. If you accidentally calibrated the iSpindel in the Plato unit, you can convert P to SG in the management settings of relay local web site. This only applies to iRelay, while the application receives the original iSpindle data. The device only works on 2.4ghz WiFi network. Additional thermometer The outdoor or ambient thermometer has the ability to alarm you when temperature too high or too low is. The length of the sensor can be extended without affecting the measurement. Also, this thermometer can be placed on the fermenter shell and serve as protection against fermentation temperature controller failure (STC – 1000). In the thermometer settings, you can select the unit in degrees C or degrees F. If the relay has a built-in temperature probe then you can add a BrewSpy new device, Brewfather Custom Stream device or Grainfather custom controller to display temperature on the BrewSpy, Brewfather or Grainfather app. Temperature appears in the interval of 1,5 or 15 minutes and is sent independently of the interval of the iSpindle. Additional pressure sensor iRelay +P Nautilis iRelay + P receive data from a pressure sensor, shows it on the screen and forwards it to applications via a WiFi network. With the desired applications, you can monitor the desired values on your computer and mobile applications, depending on the type of application you are using. Currently supported applications are: BrewSpy (Send interval min 5min), SensorSpy (Send interval min 5min), Brewfather (Send interval min 15min). Depending on the application, in case of alarm values, they will be notified via a notification on the mobile phone. The Nautilis iPressure device allows pressure units in Bar or PSI, and temperature in degrees C or F. The device is usually not purchased with a pressure sensor, but it should be ordered separately. The order link is: Here The pressure sensor has 3 wires, with iPressure you get a preparation where you have to connect these wires. You can extend the length of the pressure sensor cable as desired. When purchasing the iRelay+ please note that it is an option with included pressure sensor hardware and software –> iRelay +P. Irelay + without this option cannot have a pressure sensor, while every irelay +P can be iRelay+ Warning: If you have a black screen when turning on the device, the most common causes are: When you use a USB-c power supply, there is a chance that you do not have a "smart" charger and that the iRelay will not work even though it is declared at 5V. Try changing the cable to be USB-A to USB C, try powering through a computer or laptop, and if it works there, look for another power supply.iSpindel in Kegland Pill case option It is forbidden to send rechargeable batteries. Battery is not included in the price!!! !!! For better deal and data find Nautilis eu !!! The regular color of the iRelay case is black. The color of the Pill case can be blue or green Ispindel Pill is an electronic hydrometer used for the fermentation of beer or wine. Its angle changes during fermentation, it reads that angle and calculates the final gravity (FG) using the previously entered original gravity (OG). When the device is reset, it opens an access point (AP) to which you connect with a laptop, mobile phone or tablet. Configuration is done through the web interface. During fermentation, the data is sent over WiFi to a remote computer that collects it. It can be MQTT broker, Ubidots server, Influxdb, Prometheus push gateway, custom HTTP TCP / IP server, etc ... The device has a built-in and digital temperature sensor whose data is sent along with FG data. The unit comes without battery. It accepts 18650 Lipos with flat top, or button top. It also accepts batteries wirh current/under/over voltage protection, up to 71 mm in length. Inside is a battery charging module with a one micro USB, and one USB C connector. Charge the device by unscrewing the lid and connecting it to a mobile phone charger. Inside is also a switch for turning device off. Charging can be done when iSpindel is powered off. In this configuration, the angle will be approximately 27 degrees, which is in the recommended range of 25-30 degrees. It has 2x silicone O-ring for better sealing so you can be sure there will be no leaks. The Pill tube was tested at a pressure of 4 bar, or almost 60 psi. There were no traces of water in the case, and this result provides reliable assurance for pressure fermentation. The unit uses Kegland Pill tube THIS IS NOT A KIT. I'm selling a fully functional sample. You mush have your own 18650 lipo battery for device to work (If you are outside EU). Device has been tested, but not calibrated. BEFORE USING THE DEVICE, IT IS NECESSARY TO CALIBRATE IT, following the instructions given on the websites. WHAT YOU GET: 1 pcs 5V Nautilis iSpindel WiFi device fully connected with 2" TFT LCD screen in 3d printed case.- Ambient thermometer built into the box or on 2 meter cable depends on order -Hardware and software support for the pressure sensor if you order these option -1 pcs 2.4G Wireless Antenna,- iSpindel if you selected that option -Personal Support and assistance, -Free firmware updates on iRelay website WHAT IS NOT INCLUDED: - 5V USB C mobile phone charger for powering device - - Pressure sensor DELIVERY:I send shipments as a priority and provide a tracking number. Approximate delivery time: UK approx. 7 days, Germany approx. 7-15 days, US approx. 10-20 days

Price: 9 USD

Location: Cakovec

End Time: 2024-11-07T20:36:38.000Z

Shipping Cost: 0 USD