KICKER Replacment DX350 Amp Board, Oldschool MONO Amplifier complete New Board.

Description: KICKER DX350 Class “D” Replacement board with ends This Item is Brand new and unused, it is tested and working perfectly, This Item is a 100% working amplifier board and has never been installed in a case. It can be used for parts or total replacement. This board will fit in a ZR120 Case w/ some modifications to the zr120 heat sink bar. ( The mods are, you have to tap and thread new heat sink hold down bar screw hole in one location to accommodate for the offset space differences.) Class A/B " zr120 To Class D DX350. ( because the Mosfet chips are in different locations but all fit On the same bar. ) The pics are actual examples of the board you will receive picked randomly for this listing. Thanks! There are many of these listed as you can see this is from the ERA of KICKER when they were hand made by several individuals in Stillwater Oklahoma so there are SOME differences in the way they are built from one to another, THESE ARE USA HAND MADE amp Boards that are built to preform, NOT Retro new builds or anything like that. DIG? See the back ground drop RED and says KICKER ? Those are the KICKER printed bags these come in, each one will be inside of one of those Old school kicker bags, then wrapped up nice and boxed so they are not damaged, you will receive it in perfect condition. The KICKER bags are from the shows back in the day, back in the resolution days, In the XPL days, ZR and DX made in the USA days! At no time in the history of this board could you have bought the parts to build this item or even come close for the amount these are marked at. Seriously - what are you waiting for? As I stated before, this is a finished, working amplifier board that has never been installed in a case. It needs a Case that you will provide and a module and a Remote gain if you want. I will not accept returns on these items due to the delicate nature of the electronics. Check my feedback :0) You will receive exactly what is in the pictures. MADE IN THE USA back in the Day. Thanks for looking!! Below are specs for the DX350. This listing is made by ME, All my writing is written by me and these pictures are mine and original. These replacement boards are VERY RARE. Don’t pass this deal up. I have a limited quantity. There is no other place to get these. DX350 mono subwoofer Amplifier: This amp is a high-efficiency Class D Amplifier. That means you'll be able to get the most out of your charging system. The result is clean, loud sound! Kicker has equipped the DX350 with state-of-the-art features like a Pulse Width Modulated power supply controller, so you get full power even when your electrical system approaches peak use or low voltage. A temperature sensor ensures that the amp won't "run hot" and cause distortion. This amp Board has a Phone jack for Remote gain plug in and Module docking port. You will use your module and your gain – a remote gain is not a necessity to run this amp however a module is. a regular Phone cord will work for your gain, if you do not have a remote gain KNOB from this ERA, use one from another Era, they work the same, I have used ix 454 gains, kx gains, sx gains, I would not be surprised if just about any gain knob would work. EVEN ROCKFORD LOL. Key Features: Class D circuitry frequency response 10-200 Hz 175 watts x 1 at 4 ohms 350 watts x 1 at 2 ohms requires 8-gauge power and ground leads — wiring and hardware not included with amplifier MOSFET power supply module docking port with two-way active crossover (can be set for high- or low-pass at 60, 80, or 100 Hz, 24 dB/octave) preamp outputs can pass a full-range signal or be set for high- or low-pass at 60, 80, or 100 Hz, 24 dB/octave oversized power connectors remote gain controller 12-5/16"W x 3"H x 10-1/16"D Features Detailed Class D amplifier: The high-efficiency Class D power supplied in the KICKER DX amps lets you squeeze the absolute maximum out of your charging system. Unlike inefficient standard amps that operate at around 50-60% efficiency at full power and an even lower 30% at one-fourth power DX amps operate at an incredible 70-80% efficiency across the entire power range. Line Output: The gold-plated RCA outputs on this amplifier are able to send a signal to a second amplifier. They can send a low-pass, high-pass, or full-range signal using the included crossover. Speaker Output: There are two +/- pair of terminals, but they are connected together internally and they provide mono output. If two 4-ohm speakers are connected, one to each set of terminals, the amplifier will see a 2-ohm load, because the terminals are internally wired in parallel. Protection Circuitry: Reverse polarity, Thermal, short circuit, and over voltage circuits are used to help protect the amplifier from damage and ensure reliable operation. LED Condition Indicators: A red power LED and a yellow protection LED are used to report the amp's operating status. Controls Right Side of Amplifier: Input Gain Control: the gain control is variable from 150mV to 3V Subsonic Filter Switch: the subsonic filter engages at 25Hz and has a slope of 24 dB/octave. It can be turned on or off. Remote Gain ControlcJack: phone type jack, the remote control is 1.275" tall, 2.158" wide, and 2.122" deep (3.054" including the knob). This replacement board does not come with a a remote gain knob. Pics are actual. Inputs and Outputs Right Side of Amplifier: Line In Connections: two gold-plated RCA jacks Line Out Connections: two gold-plated RCA jacks Remote Gain Control Jack: phone-type jack Docking Port: for crossover module Speakers Outputs: two pair of gold-plated set screw terminals; direct input up to 8 gauge wire. These two sets of terminals are internally wired in parallel. Left Side of Amplifier: +12V: gold-plated set screw terminals; direct input up to 8 gauge wire Ground: gold-plated set screw terminals; direct input up to 8 gauge wire Remote Turn-On Lead: gold-plated set screw terminals; direct input up to 8 gauge wire Specifications Under Rated these amps and all KICKER amps will have a greater Output than these basic specs. 450 to 500 + watts is not uncommon for the DX350/ Power Output (at 14.4 volts): 175 watts at 4 ohms 350 watts at 2 ohms Signal-to-Noise Ratio (S/N): 100dB Total Harmonic Distortion (THD): Less than 0.3% at 4 ohms Less than 0.6% at 2 ohms Best Frequency Response: 10Hz to 200Hz (+/-2dB) Input Sensitivity: 150mV-3V Input Impedance: 22 k Ohms Fuse Rating and Type: two 25-amp blade fuses Thanks For choosing KICKER for your winning System! Feel free to email me with any questions; I am sitting here waiting to help you most of the time KICKEN IT! ;O) imeverlast MD Beames Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4

Price: 109 USD

Location: Meridian, Idaho

End Time: 2024-08-21T10:30:07.000Z

Shipping Cost: 19.8 USD