kicker kx850.2 2 channel amp old school tested and works

Description: Had this amp in my last car worked awesome before car was sold. Pulled the whole system before selling the car. Amp has a little surface rust on the left hand side but still works great! RMS Power Output (Watts x Channels)295 x 2Peak Power Output (Watts x Channels)---Power at 2 Ohms (Watts x Channels)425 x 2Power at 1 Ohm (Watts x Channels)---Bridged Power (Watts x Channels)850 x 1Minimum Impedance Bridged4Minimum Impedance Unbridged2Minimum Impedance2Best Frequency Response20-20k HzTHD at Rated RMS Power1%Signal to Noise Ratio95 dBInput Voltage14.4vFeaturesAmplifier ClassABLow-Pass Crossover Frequency50-200 HzLow-Pass Slope (dB/octave)12 dBHigh-Pass Crossover Frequency50-200 HzHigh-Pass Slope (dB/octave)12 dBBass Boost0-18 dBBass Boost Frequency40 HzFan CooledYesFuse Rating40 x 3Speaker Level Inputs---Preamp Outputs1 pairWidth (inches)25-13/16Height (inches)2-9/16Depth (inches)9-15/16Parts Warranty2 YearsLabor Warranty2 YearsProduct ResearchFeaturesInputs and Outputs NotesSpecificationsWiring RecommendationFeaturesEndKaps: The Kicker KX850.2 amplifier features two removable, cast aluminum EndKaps that are mounted to each end of the amplifier. These EndKaps protect and hide all of the wiring connections to the amplifier, and must be removed before the amp is mounted. The EndKaps can be prepped and painted any custom color you choose. They are mounted to the amp with 4 Allen-head screws (3mm Allen wrench supplied).Kicker "Living Loud" Certified Power Certificate: The amplifier comes with a certificate that informs you of the total maximum wattage of the particular amplifier, along with the model number, serial number, tested date, and whether the amplifier passed the total harmonic distortion, signal-to-noise ratio, and protection circuit tests. For example, the actual amplifier reviewed by Crutchfield was certified at 942 watts total maximum power output, although it is rated at 850 total watts (at 2 ohms in stereo).Top-mounted Controls: The KX850.2 features three rotary controls on the top panel: input gain control, bass boost control and crossover frequency control. These controls can be easily accessed, even with the EndKaps installed.Variable Active Crossover: With the amp's built-in crossover, you can switch between high-pass operation for filtering out bass information to your speakers, low-pass for subwoofers, or off for full range operation. The cutoff frequency is continuously variable from 50 to 200Hz with a 12dB/octave slope.SORT (Short circuit, Over-voltage, Reverse polarity, Thermal) Protection Circuitry: The SORT protection circuitry guards against accidents and undesired operation. If the red Protection LED illuminates, SORT has been engaged and the amplifier is in protect mode until the problem is resolved.KickBass Bass Boost: The KickBass bass boost circuit provides up to 18dB signal boost at 40Hz.SAMS (Stereo And Mono Simultaneously): With the proper high- and low-pass crossovers, this amplifier can run satellite speakers in stereo and a mono subwoofer simultaneously.Remote Bass Level Control: The dash-mounted remote unit allows you to adjust the output level of the amplifier. This can only be used when the amplifier's crossover switch is set to Lo-Pass. The remote control has the following dimensions: 2.2" W x 1.788" D (2.193" including the knob) x 1.186" H.Inputs and Outputs NotesGold-plated Connectors: The KX850.2 uses custom-tooled, gold-plated connectors to assure maximum power transfer and damping. The power, ground, remote, and speaker connections feature set-screw terminals. A 3mm Allen wrench is supplied to loosen or tighten the Allen-head set screws. The RCA line inputs and outputs are also gold plated.Speaker-level Inputs: High-level input connections are included to allow use with sources that do not have RCA preamp level outputs. A 12" speaker-level input harness with a 4-pin Molex plug on one end is provided.PAST RCA Line Outputs: The line outputs, called PAST outputs (Pre Amp Signal Transfer), allow you to pass an unfiltered preamp-level signal from this amplifier to another amplifier. This eliminates the need to use RCA splitter cords to distribute signals to two amplifiers. Note: Regardless of whether you use the RCA inputs or the speaker-level inputs on this amplifier, you will still be able to use the RCA outputs.SpecificationsDynamic Power Rating (measured at 14.4V):Per Channel Into A 4-Ohm Load: 295 watts x 2 (1% THD+N)Per Channel Into A 2-Ohm Load: 425 watts x 2 (1% THD+N)Bridged Into A 4-Ohm Load: 850 watts x 1 (1% THD+N)Continuous Power Rating (measured at 12.5V):Per Channel Into A 4-Ohm Load: 180 watts x 2 (0.085% THD+N)Per Channel Into A 2-Ohm Load: 360 watts x 2 (0.5% THD+N)Bridged Into A 4-Ohm Load: 650 watts x 1 (0.5% THD+N)

Price: 450 USD

Location: Trevor, Wisconsin

End Time: 2024-10-09T20:55:52.000Z

Shipping Cost: N/A USD