HS5157 Front Mount Hydraulic Steering Cylinder Seal Set for SeaStar HC5345 5358

Description: HomePaymentReturn PolicyAbout usContact us Details FITMENT: This HS5157 Front Mount Hydraulic Cylinder Seal Kit is designed as a replacement front seal for pivot/front mount cylinders. COMPATIBLITY: Fits Parts: for HC5340, HC5341, HC5342, HC5343, HC5344, HC5345, HC5346, HC5347, HC5348, HC5358, HC5365, HC5375, HC5394, HC5445, HC6750, HC6751, HC6752, HC6753, HC6754, HC6755 Cylinders. HS5157 KIT CONTAINS: Two seals/caps (one for each end of cylinder body), a spanner wrench tool needed to remove seal caps, all necessary o-rings. SUPERIOR MATERIAL: Made of high-quality aluminum, steel, rubber, can be used for a long time use in marine environments., will not rust and wear. High precision ensure years of trouble-free use. FUNCTION: Used to repair leaking or weeping cylinder seals. Rebuild the outboard front mount hydraulic cylinders, preventing the leaking of fluid and optimizing efficient performance Model Reference:Seal Kit for HC5345, HC5340 and HC5342 (threaded end gland), HC5347 (Pivot Cylinder, Honda 115-130 specific), HC5348 (Pivot Cylinder, OMC 77-90 specific), HC5365 (Compact Cylinder (threaded end gland)) and HC5394 (SeaRay Compact Cylinder (obsolete) (threaded gland)). Please Noted: Please make sure your cylinder shaft is not pitted or corroded. A damaged cylinder shaft may still leak even with new seals. Using Instruction: 1. Loosening the Seal Gland. Turn the outboard hard to port; place the pin wrench in the holes of a gland. And use a 5⁄8-inch box wrench on the nut on the port end of the piston rod. (NOTE:Turn counterclockwise on the pin wrench with opposite pressure on the box wrench to loosen the seal gland) 2. Removing the Support Bracket. Use a 3/4-inch socket wrench to remove the nut and washer securing the support bracket to the support rod. (Do the same to the piston rod nut and washer. ) Use wrenches on the opposite ends to keep the rods from turning. With hardware gone, pull off the support bracket. 3. Use the pin wrench to remove the Old Seal Gland. 4. Install the New Seal Gland. Place the tapered guide tool from the kit on the end of the piston rod and lubricate it and the piston rod well with oil or grease. Carefully slide the new seal gland over the guide and onto the piston rod until it reaches the cylinder. Screw the seal gland into the cylinder, but don't tighten it yet. Remove the guide tool; it is not part of the final assembly, but you will need it for the other side. 5. Reinstall the Support Bracket. Reconnect the support bracket to the support rod and piston rod and replace the washers and nuts, tightening the nuts against the washers. You may need to use wrenches on the opposite nuts to tighten sufficiently. 6. Tightening the New Seal Gland. Use the pin wrench to tighten the new seal gland while using a 5⁄8-inch box wrench on the starboard end of the piston rod for counter torque. Packaged Included: 2 x Seals/caps (one for each end of cylinder body) 1 x Pin Wrench Tool (Needed to remove seal caps) 8 x O-rings Shipping PolicyPayment MethodReturns PolicyShipping Policy Payment MethodThis is the description of Payment Method. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Returns PolicyThis is the description of Returns Policy. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Copyright©2018 DataCaciques shoppingfunday Details FITMENT: This HS5157 Front Mount Hydraulic Cylinder Seal Kit is designed as a replacement front seal for pivot/front mount cylinders. COMPATIBLITY: Fits Parts: for HC5340, HC5341, HC5342, HC5343, HC5344, HC5345, HC5346, HC5347, HC5348, HC5358, HC5365, HC5375, HC5394, HC5445, HC6750, HC6751, HC6752, HC6753, HC6754, HC6755 Cylinders. HS5157 KIT CONTAINS: Two seals/caps (one for each end of cylinder body), a spanner wrench tool needed to remove seal caps, all necessary o-rings. SUPERIOR MATERIAL: Made of high-quality aluminum, steel, rubber, can be used for a long time use in marine environments., will not rust and wear. High precision ensure years of trouble-free use. FUNCTION: Used to repair leaking or weeping cylinder seals. Rebuild the outboard front mount hydraulic cylinders, preventing the leaking of fluid and optimizing efficient performance Model Reference:Seal Kit for HC5345, HC5340 and HC5342 (threaded end gland), HC5347 (Pivot Cylinder, Honda 115-130 specific), HC5348 (Pivot Cylinder, OMC 77-90 specific), HC5365 (Compact Cylinder (threaded end gland)) and HC5394 (SeaRay Compact Cylinder (obsolete) (threaded gland)). Please Noted: Please make sure your cylinder shaft is not pitted or corroded. A damaged cylinder shaft may still leak even with new seals. Using Instruction: 1. Loosening the Seal Gland. Turn the outboard hard to port; place the pin wrench in the holes of a gland. And use a 5⁄8-inch box wrench on the nut on the port end of the piston rod. (NOTE:Turn counterclockwise on the pin wrench with opposite pressure on the box wrench to loosen the seal gland) 2. Removing the Support Bracket. Use a 3/4-inch socket wrench to remove the nut and washer securing the support bracket to the support rod. (Do the same to the piston rod nut and washer. ) Use wrenches on the opposite ends to keep the rods from turning. With hardware gone, pull off the support bracket. 3. Use the pin wrench to remove the Old Seal Gland. 4. Install the New Seal Gland. Place the tapered guide tool from the kit on the end of the piston rod and lubricate it and the piston rod well with oil or grease. Carefully slide the new seal gland over the guide and onto the piston rod until it reaches the cylinder. Screw the seal gland into the cylinder, but don't tighten it yet. Remove the guide tool; it is not part of the final assembly, but you will need it for the other side. 5. Reinstall the Support Bracket. Reconnect the support bracket to the support rod and piston rod and replace the washers and nuts, tightening the nuts against the washers. You may need to use wrenches on the opposite nuts to tighten sufficiently. 6. Tightening the New Seal Gland. Use the pin wrench to tighten the new seal gland while using a 5⁄8-inch box wrench on the starboard end of the piston rod for counter torque. Packaged Included: 2 x Seals/caps (one for each end of cylinder body) 1 x Pin Wrench Tool (Needed to remove seal caps) 8 x O-rings Shipping PolicyReturns PolicyContact usShipping Policy 1.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay. 2.Fast shipping by USPS, UPS, DHL or Fedex. It will takes about 5-7 business days for delivery. Items will be shipped within 2 business days when we received payment. 3.If your shipment delays, we hope you can be patient, and at the same time contact us, we will try our best to help you.Returns Policy1.If any item is defective upon receipt or do not work, please contact us for the return address, return is accepted within 30 days after the buyer receiving the item. 2.Returned item has to be in its original condition. Buyer is responsible for return shipping costs . 3.After receiving the return we will make a replacement depends on our available stock, if not available, a refund will be issued.Contact us 1.Please be patient when contacting us, all messages will be replied within 12 hours. 2.Please let us know immediately if a package is damaged upon arrival. 3.Feel free to contact us if you’d like to combine shipping on your purchases. 4.We appreciate your feedback and we will send buyers positive feedback after a shipment has been processed. 5.Customer satisfaction is significant to us. If you are dissatisfied with a transaction for any reason. Before taking any action, please contact us through eBay and we will do everything we can to help you. Copyright©20Than18 DataCaciquesOn Mar 1, 2024 at 14:55:44 PST, seller added the following information:

Price: 19.99 USD

Location: Ontario, California

End Time: 2024-10-01T21:50:22.000Z

Shipping Cost: 0 USD