NISMO

HI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished Board

Description: Introduction: ● B22 (beta 22) is a high-end, reference-quality DIY stereo amplifier for dynamic headphones. It could also be built as a power amplifier for speakers (18Wrms into 8Ω unbalanced, or 50Wrms into 8Ω fully-balanced), or as a preamplifier. ● The all-discrete (no integrated circuits), fully complementary and cascoded topology, high-current MOSFET output stage, full class A operation and carefully tuned operating points provide vanishingly low distortion, high speed, wide bandwidth, low output impedance, and high output power. All elements of the design were critically examined to create an amplifier that performs as well on the test bench as it does with music. ● The B22 is the result of a community service project for the audiophile hobbyist. The schematic diagram is open source. The circuit design, as well as the printed circuit board layout are the work of AMB with participation from the DIY community. It is designed to be relatively easy to build, but it is not recommended as a first-time project for the beginner. ● The B22 project is primarily centered around the main amplifier board. Each PCB supports one channel. ● The B22 amplifier board does not include a power supply (PSU). It needs a separate dual-rail DC supply to provide power to the circuit. ● The current draw from the β22 board is approximately 200mA per board as a headphone amplifier, depending on its quiescent current (bias) adjustment settings. As a speaker amplifier, the current draw could have peaks of over 5A per β22 board, while it idles at the same 200mA. It is a good idea to use a power supply with some headroom above the maximum draw. ● Always measure the actual output voltage of the power supply before connecting it to the amplifier for the first time, to make sure its output voltage is as expected. ● The recommended configuration for the β22 is to use an outboard power supply. This allows the power transformer and other AC components to be located far away from the sensitive amplification circuitry for minimum induced hum and noise. You may instead use a large chassis and put all β22 amplifier boards and the power supply in it, but be sure to position the power transformer and other AC components as far from the amplifier boards as possible. A toroidal power transformer is recommended in this setup for its lower magnetic field leakage. Commissioning steps: Step 1: Adjust the 501 blue adjustable resistor at the bottom, and measure the voltage at both ends of the 0.25W 2K2 resistor to be DC 4.4V. Step 2: Adjust the top 501 blue adjustable resistor, and measure the voltage at both ends of the 3W 2R2 resistor to be DC 440mV. Step 3: Adjust the middle 502 blue adjustable resistor, and measure the voltage at both ends of OUT and GND to be close to DC 0mV. Input voltage: DC +/-24V --- +/-30V. PCB Size: 155mm*50mm This is mono. If you want to build a stereo amplifier, you need to buy 2 PCS. NOTE: We have DIY kit and Finished board(Optional) ◆ DIY kit ---- All parts need you to solder and test it. ◆ Finished board ---- All parts have been welded and tested OK.

Price: 36.99 USD

Location: FOSHAN

End Time: 2024-12-04T07:46:27.000Z

Shipping Cost: 0 USD

Product Images

HI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished BoardHI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished BoardHI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished BoardHI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished BoardHI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished BoardHI-END B22 MONO Headphone Amplifier Base On Beta 22 DIY Kit/Finished Board

Item Specifics

Return shipping will be paid by: Buyer

All returns accepted: Returns Accepted

Item must be returned within: 30 Days

Refund will be given as: Money Back

Brand: GZLOZONE

Type: Headphone Amplifier

Number of Channels: 1

Product Code: HA-K/B202218

Model: B22

Country/Region of Manufacture: China

Available Variations

Color: DIY kit

Price: 36.99 USD

Available Quantity: 4

Quantity Sold: 0

Color: Finished board

Price: 43.99 USD

Available Quantity: 4

Quantity Sold: 0

Recommended

One Pair Ver 2.0 Single-ended PASS A3 Class A Amplifier Kit / Board 30W+30W
One Pair Ver 2.0 Single-ended PASS A3 Class A Amplifier Kit / Board 30W+30W

$125.00

View Details
CRC-A5 Schottky CRC Rectifier Filter Power Supply Bare PCB For PASS A3/A5
CRC-A5 Schottky CRC Rectifier Filter Power Supply Bare PCB For PASS A3/A5

$10.99

View Details
Lehmann Class A Headphone Amplifier LEM Preamplifier Kit/Board With Protection
Lehmann Class A Headphone Amplifier LEM Preamplifier Kit/Board With Protection

$76.99

View Details
Purple Gold LEM HIEND Class A Headphone Amplifier Base On Lehmann Preamp Circuit
Purple Gold LEM HIEND Class A Headphone Amplifier Base On Lehmann Preamp Circuit

$172.29

View Details
GZLOZONE MMCF10 HIFI LP Phonograph MM Amplifier RIAA Phono Preamplifier PCB
GZLOZONE MMCF10 HIFI LP Phonograph MM Amplifier RIAA Phono Preamplifier PCB

$7.99

View Details
ZEROZONE HIFI Mono High Power TPA3255 Class D Digital Power Amplifier 300W
ZEROZONE HIFI Mono High Power TPA3255 Class D Digital Power Amplifier 300W

$321.69

View Details
MC22 ECC83 Tube Preamplifier Base On McIntosh C22 With TREBLE/Bass Adjustment
MC22 ECC83 Tube Preamplifier Base On McIntosh C22 With TREBLE/Bass Adjustment

$329.99

View Details
2 Channel ZEROZONE X-ONE FET+BJT+MOS Class A Or AB Power Amplifier PCB 5W Or 30W
2 Channel ZEROZONE X-ONE FET+BJT+MOS Class A Or AB Power Amplifier PCB 5W Or 30W

$15.99

View Details
GZLOZONE DUAL-RIAA MM Phono Turntable Preamplifier PCB MM LP Amp DIY
GZLOZONE DUAL-RIAA MM Phono Turntable Preamplifier PCB MM LP Amp DIY

$7.99

View Details
DC5V-24V Ultra Low Noise STUDER900 Linear Power Supply Regulated Board / Kit
DC5V-24V Ultra Low Noise STUDER900 Linear Power Supply Regulated Board / Kit

$15.99

View Details