Handheld 2.8" Display Tiny Spectrum Analyzer TinySA ULTRA With 4" Display

Description: There are 2 options, TinySA and TinySA Ultra, pls see below detials for differents,any doubts,feel free to ask TinySA model comparison table： tinySA tinySA Ultra Display size 2.8 inch 4 inch Max low input frequency 350MHz 800MHz, 6GHz in Ultra mode High input range 240MHz - 960MHz Not available Resolution filters in 1,3,10 steps from 3kHz to 600kHz from 200Hz to 850kHz Max low output frequency 350MHz Sine wave up to 800MHz, Square wave up to 4.4GHz Low output level -76dBm to -7dBm -104dBm to -16dBm High output frequency range 240MHz - 960MHz Not available High output level -32dBm to 16dBm Not available Ultra mode Not available Level calibrated up to 6GHz Internal LNA gain Not available 20dB up to 4GHz Internal step attenuator Normal: 0-31dB, High: NA 0-31dN Displayed points per scan max 290 max 450 0-350MHz scan time 405ms 165ms Shortest zero span time 1.8ms 17ms DANL low input at 100MHz -146dBm/Hz -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) DANL high input at 880MHz -163dBm/Hz Not available DANL degrading in ultra mode 10dB above 2.5GHz, 25dB above 5.3GHz Phase noise at 10kHz offset -83dBc/Hz -92dBc/Hz Phase noise at 100kHz offset -98dBc/Hz -108dBc/Hz Low input 1dB compression level -0.5dBm +0.5dBm (LNA Off) / -26.5dBm (LNA On) IIP3 without LNA +24dBm +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) IIP3 with LNA Not available -8dBm (at least 2MHz apart) SD card slot Not available micro SD card Audio out Not available 3.5mm headphone plug FW update mode activation Via DFU menu Push jog button before switch on AM modulation depth Fixed 30% 10% and 100% FM deviation 4kHz or 75kHz 1kHz to 300kHz Modulation frequency 50Hz to 5kHz 50Hz to 5kHz(AM) or 1kHz(FM) TinySA Option: User interface: * Display resolution 320*240 pixels * Screen diagonal 2.8" * 16 bits per RGB pixels * Resistive touch control * Jog switch control * USB serial port control * Optional TTL USART port (SW not yet implemented) on the internal PCB * Linear power supply to avoid switching noise. *Add port ESD protection to upgrade version（V0.3.1_E） The input/output specification of the tinySA is split over the 4 modes Low input mode spec: * Input frequency range from 100kHz to 350MHz * Input impedance 50 ohm when input attenuation set to 10dB or more. * Selectable manual and automatic input attenuation between 0dB and 31dB in 1 dB steps * Absolute maximum input level without attenuation of +10dBm * Absolute maximum input power with 30dB attenuation of +20dBm for short period * Input Intercept Point of third order modulation products (IIP3) with 0dB attenuation of +15dBm * 1dB compression point at +2dBm with 0dB attenuation * Power detector resolution of 0.5dB and linearity versus frequency of +/-1dB * Absolute power level accuracy after power level calibration of +/- 1dB * Lowest discernible signal using a resolution bandwidth of 30kHz of -102dBm * Frequency accuracy equal to the selected resolution bandwidth * Phase noise of -90dB/Hz at 100kHz offset and -115dB/Hz at 1MHz offset * Spur free dynamic range when using a 30kHz resolution bandwidth of 70dB * Manually selectable resolution filters of 3, 10, 30, 100, 300, 600kHz. Automatic selection of one of the 57 resolution filters. * On screen resolution of 145 or 290 measurement points. * Scanning speed of over 1000 points/second using largest resolution filters. * Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth * Spur suppression option for assessing if certain signals are internally generated or actually present in the input signal High input mode spec: * Input frequency range from 240MHz to 960MHz * As there is no input bandfilter strong signals outside the 240MHz to 960MHz range can cause distortion of the in band signals * Absolute maximum input level without attenuation of +10dBm * Input Intercept Point of third order modulation products (IIP3) of -5dBm * 1dB compression point at -6dBm with 0dB attenuation * Power detector resolution of 0.5dB and linearity versus frequency of +/-1dB * Absolute power level accuracy after power level calibration of +/- 1dB * Lowest discernible signal using a resolution bandwidth of 30kHz of -115dBm * Frequency accuracy equal to the selected resolution bandwidth * Spur free dynamic range when using a 30kHz resolution bandwidth of 50dB * Selectable (automatic and manual) resolution filters of 3, 10, 30, 100, 300 and 600kHz * Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/- 15dB * On screen resolution of 145 or 290 measurement points. * Scanning speed of over 1000 points/second using largest resolution filters. * Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth Low output mode spec: * Sinus output with harmonics below -40dB of fundamental * Output frequency range from 100kHz to 350MHz * Output level selectable in 1dB steps between -76dBm and -6dBm * Optional AM, narrow FM and wide FM modulation or slow sweep over selectable frequency span High output mode spec: * Square wave output * Output frequency range from 240MHz to 960MHz * Output level selectable in variable increments between -38dBm and +13dBm * Optional narrow FM and wide FM modulation or slow sweep over selectable frequency span Reference generator spec: * Optional square wave output with fundamental at -25dBm connected to high input/output * Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz. Battery spec: * Charging time max 1 hour on 500mA minimum USB port or USB charger * Operation on fully charged battery for at least 2 hours Package inclued: TinySA 2.8" Spectrum analyzer *1 20cm sma-sma rg174 rf cabe *2 USB Type-C Data Cable *1 Hand rope *1 SMA female to female connector *1 SMA telescopic antenna *1 TinySA ULTRA Option: 2023 New Handheld Tiny Spectrum Analyzer TinySA ULTRA 4" Display 100kHz to 5.3GHz with 32GB Card Version V0.4.5.1 Specification： Parameter Specification Display size 4” TFT LCD (480×320) Max low input frequency 800MHz, 6GHz in Ultra mode Resolution filters in 1,3,10 steps from 200Hz to 850kHz Max output frequency Sinus up to 800MHz, Square wave up to 4.4GHz output level -104dBm to -16dBm Ultra mode Level calibrated up to 5.3GHz Internal LNA gain 20dB up to 4GHz Displayed points per scan max 450 0-350MHz scan time 165ms Shortest zero span time 17ms DANL at 100MHz -153dBm/Hz (LNA Off) / -169dBm/Hz (LNA On) DANL degrading in ultra mode 10dB above 2.5GHz, 25dB above 5.3GHz Phase noise at 10kHz offset -92dBc/Hz Phase noise at 100kHz offset -110dBc/Hz Input 1dB compression level +0.5dBm (LNA Off) / -26.5dBm (LNA On) IIP3 without LNA +18dBm (at least 2MHz apart) / 0dBm (500Hz apart) IIP3 with LNA -8dBm (at least 2MHz apart) Frequency stability <1ppm ( -10℃ ~ +55℃) SD card slot micro SD card Audio out 3.5mm headphone plug FW update mode activation Push jog button before switch on Maximum current consumption 330mA Maximum charging current 1300mA Battery Li-polymer 3.7V 3000mAh RF connectors SMA female Communication Interface USB-CDC(Type-C)，UART-TTL(2.54mm Connector) Appearance Size 117x72x23mm (Excluding protruding parts) Package includes: Host (with 3000mAh battery, 4"display) x 1 USB Type-C data cable x1 30cm ALSR100 SMA cables x2 SMA-SMA barrel connector x1 Antenna with SMA connector x1 Lanyard and touch plectrum x1 32GB MicroSD card(plugged in the host) x1

Price: 113.31 USD

Location: China

End Time: 2024-10-28T01:23:08.000Z

Shipping Cost: 0 USD