Fender Cyber-Twin 65 watt Guitar Amp

Description: NoteontheCyber–TwinSETMpresets Custom Shop presets were created by various players fluent in the corresponding musical styles. The appropriatemodel of guitar was used wherever possible, ala Jimi with a maple-necked Stratocaster®.Consequently, some presets may seem to be more “trebly” or “bassy” than you would prefer, or seem louder or quieter than some of the other presets. This is natural, because if person “A” plays a Telecaster® in a tiled room, and person “B” uses a Jazz guitar in a carpeted room, they will achieve very different end results. You can easily move the knob settings and store your changes if desired. Most of our Cyber-presets are designed to let the unique character of your instrument and playing style come through. That’s why thousands of pros and hobbyists alike have added the Cyber-Twin® to their tone toolbox! Your new Cyber-Twin® amplifier is the crowning achievement of Fender’s most advanced research and development project. Brought to you by the same Tone–team that created the original Cyber–TwinTM amplifier, the Cyber-Twin® is refined and updated with additional amp designs and effects. Cyber–Series amplifiers are endowed with Fender’s exclusive Virtual Tone InterpolationTM technology (patent number 6,222,110). VTITM technology enables the Cyber-Twin® amplifier to be different amplifiers according to circuit design. Starting with a virtual circuit board, the Cyber-Twin® amplifier "rewires" its fundamental architecture (tubes, resistors, capacitors, etc.) to become the essence of all the amplifier greats — Fender’s BlackfaceTM, Dyna–TouchTM, Tweed and Modern amps, and even the best of the British amps! The Cyber-Twin® amplifier allows you to be the amp designer. Start with one of 150 permanent amp and effect setups stored within the Cyber-Twin® amp—twist some knobs, make some changes, then SAVE to one of the 100 rewritable preset locations reserved onboard for your original amplifier designs. MIDI implementation on the Cyber-Twin® amplifier enables you to transfer presets to and from the amp for backup to a PC, or for exchange with other Cyber-Twin® SE amplifier players. The Cyber-Twin® amplifier also puts a huge array of studio–quality effects at your command: Reverb, Modulation and Delay effects, enough to satisfy most any sonic appetite. And many are in stereo, so you can use the line outputs or headphones to enjoy a fully ambient stereo dimension. The Cyber-Twin® amplifier’s Dyna–TouchTM power amp circuitry and Celestion®speakers deliver powerful, responsive Tone to you and your audience.The Cyber-Twin® amplifier allows you to be the amp designer. Start with one of 150 permanent amp and effect setups stored within the Cyber-Twin® amp—twist some knobs, make some changes, then SAVE to one of the 100 rewritable preset locations reserved onboard for your original amplifier designs. MIDI implementation on the Cyber-Twin® SE amplifier enables you to transfer presets to and from the amp for backup to a PC, or for exchange with other Cyber-Twin® amplifier players. The Cyber-Twin® amplifier also puts a huge array of studio–quality effects at your command: Reverb, Modulation and Delay effects, enough to satisfy most any sonic appetite. And many are in stereo, so you can use the line outputs or headphones to enjoy a fully ambient stereo dimension. The Cyber-Twin® amplifier’s Dyna–TouchTM power amp circuitry and Celestial®speakers deliver powerful, responsive Tone to you and your audience. 40 character display shows you menu options, prompts and amp design information The data wheel enables you to select a dynamic range of settings 5 modes of operation: •Play •Amp Edit •FX Edit •Utility •Tuner 8 motorized knobs automatically rotate to adjust to preset selections, MIDI continuous controller sequences and input from a MIDI pedal or analog expression pedal 250 amplifier design presets: • Fender Custom Shop – 100 custom amp designs including effects • Player’s Lounge – 100 of your own (rewritable) amp and effects designs • Your Amp Collection – 50 classic amp designs as originally manufactured MIDI implementation: • 24 continuous controllers for automatic, sequenced control of amplifier settings• An assignable continuous controller for remote control of a dynamic parameter• 4 system exclusive functions for transferring presets and updating systems 16 drive circuitry selections: • 12 tube types, • 4 solid state types including new Extreme setting 2 vacuum tubes are used in the tube drive and the analog circuitry, (12AX7WC), now externally accessible 6 tone stacks, each with 2 location parameters (before/after the drive circuitry) 43 FX (effects) selections with 4–5 adjustable parameters each: • 10 delay FX • 11 modulation FX • 3 special FX • 4 FX combinations • 14 new FX 11 Reverb types with 4 adjustable parameters each 4 compression level settings A hum reduction button to reduce line noise 3 noise gate levels with an adjustable depth parameter 8 timbre types give instant tone shaping for style accent or balance 4 line/speaker phase settings allow you to reverse the polarity of each speaker independently 8 reverb/effects bypass combinations (or vibratone rotor speed) that you can toggle by footswitch 4 quick access keys for one button access to favorite amp design presets 4 button footswitch for hands free selection of your quick access presets The expression pedal jack allows you to control nearly every preset controllable parameter with an analog expression pedal (optional) 130 watts of stereo output power, (65 watts per channel) Two 12AX7 preamp tubes Two 12 inch, 8 ohm Celestion® G12T-100 speakers 1 stereo digital line output, RCA SPDIF jack for connection to digital sound equipment 2 stereo XLR impedance balanced output jacks, with mono/stereo selection switch 3 effects loop jacks (mono out, and mono or stereo in) with -10dbv/+4dbu switch 2 speaker extension jacks for experimenting with other external speaker cabinets This page introduces key concepts for the basic operation of your Cyber–Twin SETM. The following pages provide an overview of each item on the front and rear panels. The DISPLAY shows vital information and menus for the Cyber-Twin® The DATA WHEEL works dynamically with the display giving you full control over preset selection, effect parameters and system configuration. The display also responds to the use of panel knobs or buttons providing useful information. You can enter different MODES to edit amplifier designs, effects and system utilities; each mode determines the functions of the display and data wheel. PLAY MODE is active whenever the Cyber-Twin® amplifier is first switched on. After booting up, the display will show information about the current preset. The first line displays the preset location (bank/number) and name. The second line displays the type of tone stack controls (treble, middle, bass), tone stack location (pre/post distortion) and the active effect. In play mode, the data wheel selects presets. There are three banks of PRESETS. The FENDER CUSTOM SHOP (C00-C99) and YOUR AMP COLLECTION (A00-A49) are permanent presets. ThePLAYER’S LOUNGE (P00-P99) presets are rewritable for you to save your own amp and effect designs. The Cyber-Twin® is instantly reconfigured to the settings saved within a selected preset. The 8 MOTORIZED knobs on the Cyber-Twin® automatically adjust to the preset settings. You can safely interrupt knob rotation anytime by manually stopping it. Note that the display will temporarily indicate knob position when turned manually. Changes you make to amplifier settings (volume, tone, effects, etc.) will be lost upon selecting a different preset or turning the amplifier off, unless you save them. SAVE simply by pressing SAVE, selecting a Player’s Lounge preset to overwrite and pressing SAVE again. The SAVE LED blinks as a reminder to save settings once a change is made. NOTE: MEMORYPROTECTION must be disabled before you can save! (see page 24). AMP EDIT MODE, FX EDIT MODE and UTILITY MODE are activated by pressing the corresponding buttons to the right of the display. Use these modes for modifying amp design, selecting and editing effects and for system management. TUNER MODE is activated using the TUNER button; use it to tune your guitar. PLAY MODE is reactivated by pressing EXIT. Use it to play guitar! Two FOOTSWITCHES are supplied with your Cyber-Twin® SE. Connect them to the appropriate rear panel jacks to enable remote selection of your Quick Access buttons and Reverb/Effects bypass.A. INPUT JACK Input connection for your guitar. TRIM Sets the input signal level for proper analog–to–digital conversion. Adjust TRIM so that most of the green LEDs stay on at normal playing levels and the red LEDflashes occasionally while playing at peak intensity. This knob is not preset programmable nor motorized. GAIN Adjusts the distortion level and contributes to overall amplifier loudness. Use VOLUME {D} to compensate for any undesired volume level change resulting from a GAIN level change. VOLUME Adjusts the post–distortion signal level and contributes to overall amp loudness. Use in conjunction with GAIN {C} to normalize volume differences between presets. Several knobs affect the overall loudness of the amplifier: Knob Function TRIM Supply proper signal level to DSP GAIN Adjust distortion level VOLUME Equalize level differences between presets MASTER Global volume and maximum level governing E. TREBLE / MIDDLE / BASS Preset MIDI Programmable Controllable NO NO YES YES YES YES NO YES Expression Pedal Controllable NO YES YES YES Front Panel Overview 9 Adjusts tone in the high–, mid–, and low–frequency ranges respectively. PRESENCE Adjusts tone in the ultra-high frequency range after the distortion circuitry for a crisp tone sparkle. REVERB Adjusts the level of the active Reverb. Enter AMP edit mode to select Reverb types and edit Reverb parameters (see page 14). MASTER VOLUME Controls the overall loudness of the amplifier globally, independent of any preset. MASTER VOLUME is not preset programmable, although it is motorized so that it can be controlled remotely by expression pedal or MIDI. Remote operation of MASTER VOLUME is limited to a maximum value defined by where the MASTER VOLUME is set manually on the front panel. Set the MASTER VOLUME knob to the desired maximum level and motorized control will be confined to the range below that boundary.I. J. QUICK ACCESS Provides instant access to four favorite presets. To assign a button, first select the preset with the data wheel. Then, press and hold a QUICK ACCESS button. The LEDlights up when your new QUICK ACCESS button has been activated. Press the same button or corresponding footswitch button to recall the assigned preset. SAVE Saves the current amplifier configuration as a new preset. 1) Press SAVE once and a Player’s Lounge preset location is displayed. 2) Select any Player’s Lounge preset to overwrite using the data wheel. Press EXIT to cancel the save operation 3) Press SAVE again and your new preset will be stored. The SAVE LED flashes after an amp setting is changed as a reminder to save. If a different preset is selected before the current configuration is saved, your changes will be lost. TUNER Turns the tuner on/off. The TUNER LEDflashes and audio is muted while the tuner scale is displayed. NOISE GATE Turns the noise gate on/off. Use it to reduce static and environmental noise transmitted through nearby electronic devices. Enter AMP edit mode to edit noise gate depth and threshold parameters (see page 14). TAP In PLAY mode, TAP sets the time/rate interval of the active effect, if applicable. Press TAP at least twice at the desired rate to set the interval by feel (the average of the last five taps is calculated for multiple taps). Press TAP once for the longest interval possible. The TAP LEDflashes at the interval rate which is also temporarily displayed. Adjust the time/rate parameter accessed in the FX edit mode for precision control of the TAP interval (see the FX menus on page 16 for details). In UTILITY mode, TAP is used to confirm menu actions. PEAK and MIDI LEDs PEAK flashes when the DSP circuit is clipping (distorting). Reduce VOLUME if undesirable distortion is heard while this LED is on, then use MASTER to the increase loudness level. MIDI is on when the Cyber–Twin SETM is communicating MIDI information. HUM REDUCTION Turns hum reduction on/off. Reduces environmental hum in some situations using a patented algorithm that seeks out line frequencies and squelches only the hum, without degrading your music! FXLEVEL/FXVAL1/FXVAL2 Adjusts the level, parameter 1 and parameter 2 of the active effect, respectively. The functions of these knobs as well as additional parameters can be accessed through the FX edit mode (see page 16). DISPLAY and DATA WHEEL Your interface for controlling the dynamic functions described throughout this manual (See the Overview on page 8). PRESET EDIT The AMP and FX buttons activate the AMP and FX (effects) edit modes respectively. For the AMP edit menus see page 14; FX edit menus see page 16. UTILITY Activates the UTILITY mode. For the UTILITY edit menus, see page 24. EXIT Activates the default PLAY mode (except during factory preset restore and MIDI data transfers). BLUE JEWELAA. POWER Switches Power on or off to the Cyber-Twin® SE amplifier. BB. IEC POWER CORD SOCKET Connection for the included power cord. Connect to a grounded AC outlet in accordance with the voltage and frequency ratings listed on the rear panel of your Cyber–Twin SETM. CC. FOOTSWITCH JACK Connect the included Fender® 4–button footswitch using the MIDI type cable provided. Use this footswitch to remotely activate the Quick Access presets. Although the footswitch uses a MIDI type cable, the footswitch is an analog device and should only be connected to the FOOT SWITCH jack. DD. EXPRESSION PEDAL JACK Connection for a standard expression foot pedal (optional) used to remotely control any of the following parameters: GAIN, VOLUME, TREBLE, MIDDLE, BASS, PRESENCE, REVERB, MASTER, any Reverb parameter, or any effect parameter. Expression pedal assignment is preset programmable through the AMP edit mode (see page 15). EE. REVERB / FX BYPASS Connection for the included one-button footswitch. Use this footswitch to remotely bypass Reverb and/or effects in one of 8 input/output configurations. Or, if Vibratone is the active effect, you can switch between rotor speeds (set Reverb/FX bypass parameter to Vibro Fast/Slow). Reverb/FX bypass is preset programmable through the AMP edit menu (see REVERB / FX BYPASS on page 15)

Price: 475 USD

Location: Plaistow, New Hampshire

End Time: 2025-01-07T14:41:51.000Z

Shipping Cost: 99 USD