Crown Ultratech 2020 Power Amp - CE2000

Description: Crown Ultratech 2020 Power Amp - Same as CE2000 Recently obtained from a pro audio rental facility that was liquidating excess equipment Unit is tested and working. No issues to report. In good condition. We cleaned it up before photographing the unit. See photos for more details. Some specs at the bottom of this listing Listing is for Crown Ultratech 2020 Power Amp - CE2000 as pictured only. No other accessories included. GRAB IT WHILE YOU CAN!At New York Music Mall LLC, we strive to make sure our customers are totally satisfied with their buying experience. If for any reason you have any issue with your purchase, please contact us and we will get right back to you and work with you to resolve any problems. Please do not open any cases or claims without contacting us first. We will be able to resolve any problems directly and make sure that any issues are taken care of immediately. Our perfect feedback speaks for itself. THANK YOU FOR YOUR BUSINESS. WE APPRECIATE IT! Specifications Note: All measurements relate to 120 volt, 60 Hz units in Stereo mode with 8-ohm loads and an input sensitivity of 26 dB gain at 1kHz rated power unless otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Power Output Power: See power charts below. Load Impedance: Safe with all types of loads. Rated for 2, 4 and 8 ohms in Stereo mode, 4 and 8 ohms in Bridge-Mono mode. Voltage Gain at 1kHz, 8 ohm rated output: CE 2000: 32.1 dB gain at 1.4 volt sensitivity; 26 dB gain at 2.83 volt sensitivity. Features Accurate, uncolored sound with very low distortion for the best in music and voice re- production. Bridge-mono/stereo mode switch allows you to set up your amps/speakers in the configura- tion that best suits your needs. Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mis- matched loads, general overheating, high-fre- quency overloads and internal faults. Extremely versatile, handling a wide range of speaker impedances and outputs. • Switchable input sensitivity. • Proportional speed fan optimizes cooling ef- ficiency. • Shallow rack depth. Only 12.25 inches deep! • Choice of Speakon®, binding post, or barrier strip outputs (Speakon® comes standard). • Choice of balanced 1/4-inch (6.35-mm), XLR, or barrier strip inputs. • The best Three-Year, No-Fault, Fully Transfer- able Warranty in the business! It even covers round-trip ground shipping in the U.S. for all warranty work. Required AC Mains: 50/60 Hz (North American units are 60 Hz only); 100, 120 and 230/240VAC (±10%) units are available. AC Line Current, CE 1000: 100V: 7.6A 120V: 6.3A 230-240V: 3.5A At Idle: Draws no more than 90 watts. CE 2000: 100V: 11.4A 120V: 9.5A 230-240V: 5.0A At Idle: Draws no more than 90 watts. AC Line Connector: NEMA 5-15P (15A). Performance Frequency Response: ±0.2 dB from 20 Hz to 25 kHz at 1 watt. Phase Response: ±15 degrees from 20 Hz to 20 kHz at 1 watt. Signal to Noise Ratio (below rated 1 kHz power): 105 dB (A weighted) 100 dB (20 Hz to 20 kHz) Total Harmonic Distortion (THD): 0.5% or less true THD from 20 Hz to 20 kHz. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) Less than 0.1% at rated power to 35 dB below rated power at 8 ohms. Damping Factor: Better than 400 from 10 Hz to 400 Hz. Crosstalk: Better than 55 dB below rated power, 20 Hz to 20 kHz. Common Mode Rejection (CMR): Greater than 70 dB from 20 Hz to 1 kHz. DC Output Offset (Shorted Input): < ±10 mV. Controls and Connectors Level: A detented rotary level control for each channel located on the front panel. Power: An on/off rocker switch located on the front panel. Mode: A two-position switch located on the back panel below the input connectors which, when turned to stereo, operates the amplifier as two independent channels. When “Bridge- Mono” mode is selected, the amplifier bridges the two output channels for twice the output voltage. Reset: A front-panel push button used to reset the circuit breaker that protects the power supply. Sensitivity: A two-position switch located on the back panel next to the Mode switch. Switchable between 1.4 volts for full output into an 8 ohm load (default setting), or a fixed volt- age gain of 26 dB. Also available as a service option is 0.775 volt sensitivity. Fault Jack: A back-panel RJ-11 jack that may be remotely monitored to signal amplifier Fault condition. An LED or other signalling device (not supplied) may be used.* Track Page Views WithAuctiva's Counter

Price: 219.09 USD

Location: Brooklyn, New York

End Time: 2024-11-11T15:12:26.000Z

Shipping Cost: 40 USD