Chem Link F1354GR Penetration Seal 4" E-Curb System Kit 1/2 gallon, New In Box

Description: Chem Link F1354GR Penetration Seal 4" E-Curb System Kit 1/2 gallon, New In BoxChem Link F1354GR Penetration Seal 4" E-Curb System Kit 1/2 gallon, New In Box Features: 4" E-Curb Exterior Rings - Qty 4 M-1 Structural Adhesive/Sealant + tip for bonding, priming, and sealing the penetration - Qty 2, 10.1 oz 1-Part "Moisture Cure" pourable sealer - Qty 1, 1/2 Gallon Rapid installation - "Slip-fit" light weight curb design No flashing or mechanical attachment required Service Temperature -40F to 200F (-40C to 93C) For sloped roof applications From the Manufacturer: Upgrade your roofing system with Chem Link's E-Curb penetration seals, a modern alternative to traditional metal pitch pans. Our E-Curb System features versatile precast components and pourable sealants, providing quick and easy installation in under 15 minutes. Say goodbye to flashing and mechanical attachment hassles forever. E-Curbs are specifically designed for PVC, EPDM, PIB, and TPO single-ply roofing membranes, offering exceptional versatility for sealing penetrations around solar panel mounts, HVAC, electrical, and structural supports. Experience peace of mind with our durable, waterproof rubber seal that ensures long-lasting protection. Crafted from lightweight nylon resin, our E-Curb precast form components deliver both strength and efficiency. Our M-1 Structural Adhesive/Sealant, included in each kit along with two cartridges and an applicator tip, provides a durable, self-fixturing solution. For seamless sealing, our 1-Part pourable sealer offers flexibility and ease of use. With its 100% solid rubber composition, low VOC content, and resistance to shrinkage and deterioration, you can trust its performance. Each E-Curb kit comes with a convenient 1/2 gallon pouch of 1-Part sealer. Upgrade your roofing sealing solution today with Chem Link's E-Curb System. Experience the difference in quality and efficiency for your e-commerce needs. Installation Instructions: Step 1: Remove all previously applied caulk, mastic, cement, asphalt and other contaminants from penetrations with wire brush Step 2: Clean all smooth substrates with isopropyl or denatured alcohol. Brush away all gravel or loose granules. Step 3: Seal the base of each penetration with M-1 and coat each penetration with M-1 to 3" above the roof line. Step 4: Hold section of E-Curb, flat side up, and apply 1/4" bead of M-1 to the entire bottom perimeter. Apply an additional 1/4" bead of M-1 down the center of the section. Do not tool the beads flat. Step 5: Place the E-Curb section on the roof surface to form a half circle around the penetration. Press down firmly until M-1 extrudes from the outside edge. Step 6: Apply M-1 to the second section of E-Curb as described above. Place the second section on the roof surface to form a circle with the first section. Step 7: Apply a bead of M-1 around the outside base of the installed E-Curb and tool to form a smooth fillet. Step 8: Cut tip off 1-Part cartridge and pierce the foil seal. Insert into caulking gun and pump E-Curb full. (See our Photoset for step-by-step instructions Condition: New This Chem Link Penetration Seal E-Curb Kit is new, unused, and comes sealed in the original packaging. Our company over purchased for a solar panel project and have excess inventory. Please view our photo set and contact us if you have any questions.CLICK BELOW FOR MORE ITEMSShippingBest OffersReturns

Price: 82.5 USD

Location: Ventura, California

End Time: 2024-09-27T16:30:24.000Z

Shipping Cost: 0 USD