Automotive 12V 24V Digital Voltage Circuit Tester Diagnostic Powerscan KZYEE US

Description: KM10 Functions 1. Perform these functions: power injection, measuring, ground testing, polarity checking, continuity testing and component activation. 2. Read the AVO meter, voltage, current, and resistance easily. 3. Press the power switch lightly and get the instant heat ground lead to energize the electrical components, such as the cooling fan, relay etc. 4. Activate the components by using the hot wire and ground lead simultaneously. 5. Determine the positive, negative and open circuit quickly. 6. Test the bad ground contacts quickly, follow and locate short circuits without wasting the fuse. 7. Test the continuity of the power switch, relay and diode quickly. 8. Protect the tool from overload through the inner circuit breaker. 9. Allow you to work in the dark areaCar Circuit Tester 12V/24V Automotive Electrical System DiagnosticKM10 Car Circuit Tester Basic Description---Kzyee KM10 super electrical probe diagnostic tool supports 12V and 24V electrical systems. ---Built-in voltage & polarity, continuity, Trailer Lights and Connections as well as signal circuit testing. it can quickly and accurately find trouble spot. ---Activating components in the vehicle or W/Ground, reading voltage display red/green polarity LED, tracing ,locating short circuits, bad ground contacts.KM10 Circuit Tester Key Features1.Highly reliable and extremely easy to use with 6m long strong cable 2.Built-in flashlight enables you to work in the dark 3.LED screen allows you to read voltage, current and resistance at the fingertip 4.With 6 Meter long electronic cable, convenient to test from the front to the rear of the car5.Test mode contain AV Voltage, DC Voltage, Current Resistance, LED, including most car circuit test system 6.Including Cigarette Lighter adapter, battery test clips, easy to get battery supply from the car 7.Circuit Breaker Protection: Ability to Power Up Components. Automatically shut-off if current exceeds 5 Amperes, it design to protect an electrical circuit from damage caused by over-current, typically resulting from an overload or short circuit.KM10 compared with other productsWarm Note: This probe is very sharp on the pointed end, easily to get hurt. Better to be more careful when performingKM10 Functions1. Perform these functions: power injection, measuring, ground testing, polarity checking, continuity testing and component activation. 2. Read the AVO meter, voltage, current, and resistance easily. 3. Press the power switch lightly and get the instant heat ground lead to energize the electrical components, such as the cooling fan, relay etc. 4. Activate the components by using the hot wire and ground lead simultaneously. 5. Determine the positive, negative and open circuit quickly. 6. Test the bad ground contacts quickly, follow and locate short circuits without wasting the fuse. 7. Test the continuity of the power switch, relay and diode quickly. 8. Protect the tool from overload through the inner circuit breaker. 9. Allow you to work in the dark area by using the built-in head light. 10. Operate the tool without looking at the menu once users are familiar with the tone. Test along the vehicle by the long cable.Work modeThere are four modes to diagnose the electrical systems, which can be accessed by depressing the Model Button and cycling through each one. DC Voltage AC Voltage Resistance DiodeVoltage&Polarity TestingCircuit Continuity Testing in Resistance modeWhile the tool is in Resistance mode , using the probe tip with chases is ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle's electrical system, When the probe tip is contacting a ground, the LCD will indicate "0.0Ω" and green LED will be on , A beep tone will sound.Activating Components in Your HandActivating Components in The VehicleTesting Trailer Lights and ConnectionsSignal Circuit TestingFor example , you suspect there is a problem with your M.A.P ? sensor circuit, then follow the procedure involved with testing this sensor. *Set the tool in AC Voltage mode, using the probe tip with chassis ground or the auxiliary ground lead. *Connect vacuum pump to MAP sensor *Connect the probe tip to the MAP sensor , Positive terminal and observe the LCD readings which should be a sine wave in normal condition, *Apply vacuum *Release vacuum and observe the LCD readingsActivating Components W/GroundProduct ImageSpecificationsDisplay: TFT color display (160 x 128 dpi) Operating Temperature: 0 to 60C (32 to 140F) External Power: 12.0 or 24.0 V power provided via vehicle batteryPackage List1 * PowerScan 1 * Rugged Blow Molded Case 1 * 20ft. Extension Cable 1 * Probe Tip 1 * Battery Hookup Clips 1 * Cigarette Lighter Adapter 1 * User ManualPaymentDelivery detailsTerms of salesAbout usContact usPayment We accept all common forms of payment such as Credit cards、Debit card、Google Pay ect. Please contact us if you need to use another method to pay. Payment should be made within 4 days after bidding ends. Otherwise a Unpaid Item case will be opened to you. We are not responsible for buyers’ local taxes. Please include your special requests in eBay note if there is any.Delivery detailsShipping methods: USPS First Class Mail Service /USPS Priority Mail Service/UPS Surepost SERVICE/ UPS GROUND SERVICE I will process your order within one business day (excluding holiday and weekend)If you have any problems, you can contact me first or local USPS, UPSTerms of salesPlease do not hesitate to leave us your PositiveFeedbackandgood review If you are satisfied with our productsIf youare unsatisfiedwith your purchase,please email us first to get a better solution before you leaveaneutralornegative feedback, we work hard to make sure every customer 100% satisfied and resolve any problem for you. Thank you for your kindness. About usWe are a professional Authorized dealers of AUTEL, LAUNCH,ANCEL,FOXWELL, OBDSTAR， AUTOPHIX, KZYEE, NEXAS,Autek ，WOYO，etc. We support remote assistance by TeamViewer if you have any difficulty in software installation. Contact usAny questions, you can feel free to contact me by ebay message or whatsapp.Due to time difference, I may not be able to reply immediately, but I will reply within 24 hoursPlease contact me first before giving negative feedback or opening case. Wish we can solve the problem peacefully. Working hours:0:00 am - 3:00 am Pacific Time， 6:00-9:00 pm Pacific Time, 11:00 pm - 12:00 pm Pacific Time. On Oct 23, 2023 at 02:46:31 PDT, seller added the following information:

Price: 68.99 USD

Location: Houston, Texas

End Time: 2024-03-26T10:33:21.000Z

Shipping Cost: 0 USD