AM32 50A 2250KV & 1850KV RC Crawler ESC Brushless Motor for 1/10 SCX10 Truck

Description: Product Description Features 1.RevvitRC is a brushless outrunner motor for car. Features14 poles of high temperature thickened super powerful magnets.Extreme compression of space, a 3110 12-slot stator is stuffed into a 37mm*24.2mm volume. lt has achieved the strongest power in the same volume and the smallest volume in the same power in the world.2.The weight of the entire motor [including wires] is only 80 g.Particularly suitable as a performance enhancing part for1:10 scale RC climbers. Maximum power output can be ob-tained in a limited space. At the same time, it minimizes the weight of the whole vehicle and lowers the center of gravitySpecificationsBrushless Motors:H3110Diameter:37mmLength :24.2mmAxle diameter :3.17mmWeight [with wire]:80gKV:1850/2250KVMagnetic Pole :14Mounting holes :25mmWithstand temp ≤220°CH3110 SpecsKV:1850KV/2250KV14 pole 12 slot stator8.4V-16.8V(2-4S)LiPo1/8" D(3.17mm) shaft output25mm Mounting holes for M3 screws80g with wires, without connector37mm diameter* 24.2mm long31*10mm statorPackage list 1 x 3110-2250KV Brushless Motors / 1 x 3110-1850KV Brushless Motors ESC: Features 1.RevvitRC AM32 50A car ESC, using high-performance imported 32-bit intelligent chipfor crawler cars, trailers, DIY and other climbing off-road model cars.Having a small volume,Characteristics of high load current.More suitable for loadingand does not occupy interior space.2.This ESC comes pre installed with the latest AM32 firmware. It has been optimizedfor climbing type model cars, making your climbing car run very smoothly and quietly,but it is also suitable for various 1/10 scale or 1/24 or smaller model cars.Built in adjustable two sets of voltage BEC, 7.4V and 8.4V respectively,with a designed current of 5A load, Used for higher torque servo steeringor adding rear lights to the sound group.3.In addition, this ESC comes with low voltage, blocking protection and runaway protection, which can be changed at the ground station according to your choice. The sine wave can be turned on to allow the motor to run smoothly at ultra-low speeds, making the climber more comfortable when climbing slowly in harsh environments. Product Details: Power supply: 2-6S Lipo ESC load current: 50A Adjustable BEC:7.4V and 8.4V 5A load current(adjustable via toggle DIP switch on ESC) Electronic Switch:Supported. If you dont need a switch, you can short the switch padson the ESC to turn on the power. Size: 30mm*17mm (not including capacitors) (ultra-small size)" Bundle:USBLink (parameterization tool) Caveats: This ESC does not support waterproofing, you can do waterproofing by yourself (please dispose of waterproofing by yourself for maintenance), if you need to adjustthe AM32 firmware parameters, you can use USBLink to connect to the computerusing a Type-C cable and install the ground station program,and select the serial port used to link to the ground station.Some issues during use: ① Before powering on, please pay attention to whether the BEC output voltage (7.4V and 8.4V) is supported by the car model receiver,servo, lighting, or other electrical equipment② After the ESC is powered on, the motor keeps beeping and the ESC controller does not respond. Please adjust the remote control throttle to the center or adjust the remote control throttle to the center.③ It is prohibited to directly touch the surface components of ESC when in use or not in use, as it may cause electrostatic breakdown and damage to ESC④ Please do not adjust the starting power and starting level of the ground station parameter adjustment interface arbitrarily. If these parameters are fully loaded, it may cause ESC to burn out directly when powered on. Package list1 x AM32 50A RC car ESC

Price: 47.97 USD

Location: JAMAICA, NY

End Time: 2024-11-10T17:31:08.000Z

Shipping Cost: 0 USD