12-24V WindZilla PMA Pelton Water Wheel Adapter Micro Hydro Generator Turbine B

Description: 12V-24V WindZilla Permanent Magnet Generator + 8" Pelton Water Wheel + 20mm to 17mm Pelton Water Wheel Adapter / Arbor For Micro Hydro Electric Generator / Turbine Front Way Side Way Sample Installation, please refer to description below for actual generator Install Diagram: foot mount NOT included Installation: 1. Mount Adapter to the PMA's 17mm shaft and secure with the 2 included setscrews. 2. Mount Pelton Water Wheel to the Adapter and secure with the 4 included M5 screws. Installation: 1. Mount to a generator with 20mm shaft, an arbor / adapter might be required 2. Some of our WindZilla generators have high torque which are suitble for micro hydro electric generation, if you want to fit this wheel into one of those, we have a 20mm to 17mm adapter that is sold sparately. Specification: Diameter 204mm, 8.03inch Shaft Diameter 20mm, 0.79inch Hub Material Aluminum Number of Mounting Holes 4 Mounting Holes Diameter 5mm Distance of Mounting Holes from Hub Center 17.5mm, 0.69inch Number of Spoons 12 Spoon Material Die Cast Aluminum Spoon Outer Diamter 46mm, 1.81inch Spoon Inner Diameter 37mm, 1.46inch Spoon Height 15mm, 0.59inch Spoon Depth 10mm, 0.39inch Weight 600g 20mm to 17mm Adapter /Arbor designed to secure the Pelton Water Wheel onto a PMA (Permanent Magnet Alternator) with 17mm shaft. The adapter is CNC machined and is made of aluminum for higher durability and corrosion resistance. Introduction This auction is for one WindZilla Permanent Magnet Generator. It is the major component in a small wind / hydro electric generation system. This generator is perfect for enthusiast who are interested in a DIY Wind Turbine Project. Video showing our bench test of the alternator at ~2300RPM Curve: Open Circuit Voltage, Reach 12V at 540RPM The above battery charging power curve is obtained from charging a 12V 88Ah battery bank with our SolarWind Hybrid Charge Controller. (not included in this listing) We have seen there are generators out there that hits 12V as few as 150 RPM. However, the amp output will not be impressive because in order to ramp up the voltage, thin wires must be used in the winding of the alternator which will impact the output in strong wind. As a consumer, this is a trade off that you have to decide. Our motors are built with a heavier focus on amp output and therefore it will reach 12V at: 540RPM Since wind speed increases with height, increases to the tower height can mean enormous increases in the amount of electricity generated by a wind turbine. Generator Specification: Voltage 12 V/24V DC Permanent Magnet Rare Earth Neodymium magnets Moisture /Corrosion Resistance Yes, sealed exterior, ball bearing, coated rotor Shaft Daimeter 17mm RPM at 12V RPM at 24V See Power Curve See Power Curve Body Material Aluminium Alloy & Steel Rotor Diameter 10cm (4 inches) Length 9cm (3.5 inches) Weight 2.44kg (5.4 lbs) Mount Yes, Foot Mount Cable Length approx. 33cm (13inch) Rotation Bi-directional, recommend clockwise 6 x 62" Wind Turbine Generator Blades + Hub + Nose Cone 6 socket fit Air-X 403 Charge Controller for Wind Generator Air-X Ametek Solar 225 AMPS A SLIP RING FOR 3 PHASE AC / DC 12 24 V WIND TUBINE. 1200 Watts 10.5 V-28 V DC Grid Tie Inverter TowerUp Wind Turbine Generator Tower Base Stand Mount Foundation Easy Up & Down 73.5mm 2 1/2" Aluminum Cable/Wire Mount WARNING !!! Rotating turbines present a serious mechanical hazard that can cause serious injury. Under no circumstances should you install the turbine where a person could come in contact with moving rotor blades. The installer of these blades is solely responsible for the use or misuse of these turbines. We assume no liability for ANY injuries caused by these products. NO OPERATING COST GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE Terms & Conditions Bidding this auction means that you agree with the following terms & conditions. All pictures and descriptions are subjected to change without notice. Items may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors. Payment Total payment = winning price + shipping & handling Insufficient payment will be charge extra US$0.50 to compensate the Paypal penalty fees. Shipping & Handling Total shipping = Base S&H + Combine S&H ( for each additional item ) a) Base S&H is the highest shipping cost of the first item. 1. Combine shipments are only available on the condition of a SINGLE PAYMENT. Auctions that are paid separately will NOT be shipped in combo and therefore, they are not qualified for shipping discounts. 2. We ship within 2 working days after payment is received and confirmed. Please allow up to 5-10 BUSINESS DAYS for item(s) with a physical address sending to the 48 states of United States & Canada. For international bidders, the shipping time varies with respect to your location. 3. Bounce backs due to incorrect shipping address will result in setback on deliveries. It is the buyer's responsibility to repay the shipping & handling fees. 4. We are not responsible for any loses or damages resulting from shipping. Return & Refund Policy No refunds after 30 days Shipping & handling & other service fees are NOT refundable All returned items must be in original packing. Items that are used/ damaged/ deformed or altered in any ways will not be accepted. A 20% restocking fee will be charged on all refunded items. E-mails E-mails are usually answered within 2~3 business days in priority order. Spams and mass e-mailing will be deleted without slightest glance. E-mails with virus or anything subjected to hacking are automatically deleted.

Price: 189 USD

Location: Point Roberts, Washington

End Time: 2024-01-16T23:14:44.000Z

Shipping Cost: 39.99 USD